FREYARA LASER FacialPure 5.0 Ultra, Brilliant Black Technology Double Handle Non-Invasive Laser Picosecond Machine with Pull Rod and Pulley, Eyebrow Remover and Tattoo Remover

The instrument must be filled with water before turning it on.

1. Open the overflow hole.
2. Insert the funnel into the water filling hole and add distilled or purified water to help prevent the internal water outlet from becoming blocked.
3. When water begins to flow out from the overflow hole, the instrument is full. Stop adding water and close the overflow hole securely.
4. Turn on the instrument and begin operation.

Tip: If the instrument is used every day, check and add water approximately every two weeks. If it is not used daily, check the water approximately once a month. Replace all water inside the instrument approximately every two months.

1. Clean the treatment area. Apply a thick layer of gel before eyebrow treatment.
2. Start from the end of the eyebrow. After treatment, wipe the gel away and follow appropriate cooling and aftercare procedures.
3. If the skin remains intact, avoid water for approximately 24 hours. If the skin is broken, keep the area dry until the skin has formed a scab and recovered.
4. For normal-colour eyebrows, begin close to the skin. If necessary, gradually increase the distance, but do not exceed approximately 1 cm.
5. Treat each eyebrow area only once during a session. Do not repeatedly operate over the same area.
6. Do not set the operating frequency too high.
7. Eyeliner treatment is not recommended for beginners. Become familiar with eyebrow treatment first.
8. Check the skin for inflammation or irritation before treatment. People who are prone to scarring or allergic reactions should use extra caution.
9. Keep the treatment area clean during recovery. Avoid friction, makeup, facial masks, alcohol, strenuous exercise and excessive sun exposure.

1. People who have undergone eyebrow removal many times.
2. People who are particularly prone to scarring.
3. People with very deep eyebrow tattoos.
4. People with unrealistic or excessively demanding expectations regarding treatment results.

1. Recommended operating distance: approximately 1–3 cm from the skin.
2. Tattoo treatment is generally not recommended for tattoos less than one year old.
3. Clean the treatment area thoroughly before operation.
4. After treatment, follow suitable cooling and skin-care procedures according to professional guidance.
5. Treat the same tattoo area only once during each session. Do not repeatedly operate over the same spot.
6. The treated area may form a scab after treatment. Avoid soaking the area before the scab forms.
7. Allow the scab to fall off naturally. Do not pick it by hand.
8. Avoid excessive sun exposure, heavy sweating and irritating foods during the recovery period.
9. The recommended interval between tattoo removal sessions is generally more than 30 days, depending on recovery.

1. Recommended operating distance: approximately 1–2 cm.
2. Temporary redness, swelling or warmth may occur after treatment.
3. Keep the treatment area clean throughout the recovery period.
4. Avoid excessive sun exposure during recovery.
5. If pigmentation remains, another session may be considered after approximately one month, depending on skin recovery.
6. Continue proper sun protection and avoid irritating skincare products.
7. During the first few days, focus on gentle skincare and recovery.
8. Avoid sauna, strenuous exercise, smoking and alcohol during the early recovery period.
9. Do not manually remove scabs.
10. Use SPF30+ sunscreen when going outdoors and continue proper sun protection.

Black Face Doll treatment is commonly used in skincare routines focused on brightening, reducing the appearance of dullness, oil control and pore care.

1. After cleansing, apply a thin and even layer of the appropriate treatment medium. Allow it to dry before operation.
2. Install the Black Face Doll treatment head. Suggested energy: 200–500 mJ. Suggested frequency: 2–5 Hz.
3. Maintain approximately 1–2 cm distance from the skin. Beginners are recommended to start at a lower frequency such as 2 Hz.
4. Treat each area once during a session. Do not repeatedly operate over the same area.
5. After treatment, gently cleanse the skin and continue with moisturizing and hydrating skincare.

Non-invasive 1064 nm Red Probe

For black and blue eyebrow or eyeliner pigment.
Energy: 200–300 mJ
Frequency: 1–3 Hz

Non-invasive 532 nm Blue Probe

For red, brown and coffee-coloured eyebrow pigment.
Energy: 200–300 mJ
Frequency: 1–3 Hz

Minimally Invasive 1064 nm Probe

For black and blue tattoos and deeper pigment.
Tattoo Removal Energy: 300–600 mJ
Spot Removal Energy: 600–1000 mJ
Frequency: 1–3 Hz

Minimally Invasive 532 nm Probe

For coloured tattoos and superficial pigment.
Tattoo Removal Energy: 300–600 mJ
Spot Removal Energy: 600–1000 mJ
Frequency: 1–3 Hz

Black Face Doll Probe

For brightening, dullness care, oil control and pore-care routines.
Energy: 200–500 mJ
Frequency: 2–5 Hz

Eyeliner Probe

Designed for eyeliner pigment treatment.
Energy: 200–400 mJ
Frequency: 1–3 Hz

1. Keep the pedal pressed during normal operation according to the device instructions.
2. Practice on suitable test material before first use to become familiar with the machine.
3. Do not repeatedly switch the machine on and off during operation.
4. Do not operate the device if the treatment area is irritated, inflamed or otherwise unsuitable for treatment.
5. Self-operation is not recommended.
6. Suitable protective eyewear must be worn during operation to prevent accidental eye exposure.
7. Before first use, the water tank must be filled with distilled or purified water.

Pulse Energy: 500–2900 mJ

Pulse Width: 3–20 ns

Frequency Speed: 1–10 Hz

Voltage: 110–240V

Power: 5000W

Wavelength: 1064 nm / 785 nm / 532 nm

Weight: 10 kg

Size: 46 × 34 × 36 cm

• Picosecond Machine × 1
• Handle × 1
• Funnel × 1
• Pedal × 1
• Goggles × 1
• Eye Protection × 1
• Operation Heads × 6
• User Manual × 1